| 162.25.0980.890.11.1503 Standard 5 Slewing Ring Bearings | Fatigue load limit Pu:0.655 kN; Recommended diameter for attachment bolts, inch G:0.5 in; A3:3.2 mm; Basic static load rating C0:15.3 kN; s1:24.3 mm; L:96 mm; d:35 mm; A5:22 mm; Recommended diameter for attachment bolts, mm G:12 mm; Recommended tightening torque for grub screw:7.4 N·m; T:45.3 mm; J:130 mm; Hexagonal key size for grub screw N:3 mm; d2:57 mm; N:14.8 mm; Housing material:Composite; |
| 162.28.1400.891.21.1503 Standard 5 Slewing Ring Bearings | Permissible sliding velocity v max.:5 m/s; Coefficient of friction µ max.:0.1; Permissible sliding velocity v min.:0.25 m/s; Tolerance shaft:h8; D:72 mm; B:60 mm; Tolerance housing:H7; Specific dynamic load factor K:10 N/mm²; Mass bushing:0.38 kg; Coefficient of friction µ min.:0.05; d:60 mm; Specific static load factor K0:20 N/mm²; |
| 62.20.1094.500.01.1503 Standard 5 Slewing Ring Bearings | Mass bearing pair:2.3 kg; r5 min.:0.6 mm; Limiting speed:5600 r/min; Calculation factor Y0:1.6; Reference speed:3600 r/min; Calculation factor e:0.4; Basic dynamic load rating C:242 kN; K:3 mm; Basic static load rating C0:270 kN; Fatigue load limit Pu:32.5 kN; D:120 mm; 2B:46 mm; Calculation factor Y1:1.7; rc max.:0.6 mm; Calculation factor Y2:2.5; d:65 mm; da max.:78 mm; T:49.5 mm; Da min.:106 mm; |
| 92.25.1502.990.11.1503 Standard 5 Slewing Ring Bearings | Limiting speed:2000 r/min; K:3.5 mm; b1:6 mm; d:130 mm; ra max.:1.5 mm; da min.:138 mm; Reference speed:1600 r/min; s max.:4 mm; B:50 mm; Mass bearing:3.8 kg; E:165.4 mm; Calculation factor kr:0.25; Basic static load rating C0:530 kN; D:180 mm; Da max.:173 mm; Fatigue load limit Pu:60 kN; d1 ≈:149.5 mm; r1,2 min.:1.5 mm; Basic dynamic load rating C:297 kN; |
| 61.25.1250.101.21.1504 Standard 5 Slewing Ring Bearings | PG:1/4 NPT; P180°:127 kN; Taconite seal:TER 123; Eye bolt:2 x 3/8-16 UNC; H1:152.4 mm; Initial grease fill:481.95 g; Cap bolt:3/4-10 UNC; Mass pillow block:94.3 kg; S:4.763 mm; P90°:180 kN; R1:87.313 mm; h:51.594 mm; Da:250 mm; P120°:116 kN; Cap bolt recommended tightening torque:515.2 N·m; H:298.45 mm; da:127 mm; L:511.175 mm; Ca:77.8 mm; P60°:301 kN; |
| 282.30.0975.013 Type 110/1100.2 Standard 5 Slewing Ring Bearings | Attachment bolt diameter G:12.7 mm; H2:30.163 mm; J max.:149.225 mm; L:187.325 mm; da:36.513 mm; B:59.531 mm; H:98.425 mm; J min.:142.875 mm; Mass bearing unit:3.15 kg; A:53.975 mm; Basic dynamic load rating C:96.5 kN; Limiting speed:6000 r/min; S:0.794 mm; s:29.766 mm; H1:47.625 mm; |
| 61.30.1320.000.11.1504 Standard 5 Slewing Ring Bearings | Calculation factor Y0:1.8; D:720 mm; Calculation factor e:0.35; Mass bearing:550 kg; Comparative axial load rating CFa:373 kN; Comparative radial load rating CF:2200 kN; d:500 mm; Fatigue load limit Pu:1460 kN; Calculation factor Y1:1.9; r3,4 min.:6 mm; Design variant/feature:TQO/WI; B:400 mm; Basic static load rating C0:20400 kN; T:400 mm; r1,2 min.:3 mm; Thrust factor K:1.69; D1 ≈:640 mm; Basic dynamic load rating C:8250 kN; |
| 162.25.1077.890.11.1503 Standard 5 Slewing Ring Bearings | d:10.875 in; db - Cone Backface Backing Diameter:11.693 in; Cg - Geometry Factor8:0.159; C1 - Dynamic Radial Rating (1 million revolutions)1:104000 lbf; C90 - Dynamic Radial Rating (One-Row, 90 million revolutions)3:27000 lbf; C0 - Static Radial Rating:212000 lbf; K - Factor7:1; Design Units:Imperial; C1 - Dynamic Radial Rating (Two-Row, 1 million revolutions)4:181000 lbf; Ab - Cage-Cone Frontface Clearance:0.09 in; |
| 162.28.1600.890.11.1503 Standard 5 Slewing Ring Bearings | Chamfer rsmin:5.00 mm; Inner-Ring Set:500ARXS2443; Number of Lubrication Holes:16; Type:RX-1; DUR/DOR F/E:568.000 mm; Lubrication Groove g:22.0 mm; Bore d:500.000 mm; Angle of Chamfer r1smin:20ยบ; Static Load Rating Co:12440 kN; Dynamic Load Rating C11:28680 kN; Backing Housing Diameter Ds:672.0 mm; Outer-Ring Set:568RXS2443; O.D. D:720.000 mm; Weight:1622.000 lb; Lubrication Hole Diameter h:12.0 mm; |
| 12.25.1600.001.21.1503 Standard 5 Slewing Ring Bearings | H1:88.9 mm; Mass pillow block:16.4 kg; PG:1/8 NPT; P60°:83.2 kN; End plug (suffix Y):EPR 8; P150°:26.7 kN; Cap bolt, SAE grade:5; Cap bolt recommended tightening torque:149.1 N·m; h:49.212 mm; R1:53.181 mm; ba:30.163 mm; A2:209.55 mm; P90°:49.8 kN; Taconite seal:TER 43; H:169.863 mm; RG:3/8 NPT; Cap bolt:2 x 5/8-11 UNC; Housing:SAF 516; Stabilizing ring:2 x SR-1516; P120°:30.2 kN; |